Te溶剂Bridgman法CdMnTe晶体核辐射探测器的制备和表征

碲锰镉(CdMnTe)作为性能优异的室温核辐射探测器材料,可用于环境监测和工业无损检测领域。本文中采用Te溶剂Bridgman法生长In掺杂Cd_0.9Mn_0.1Te晶体,制备成10 mm×10 mm×2 mm大小的室温单平面探测器,研究了该探测器对²⁴¹Am@59.5 keV γ射线源的能谱响应。通过表征红外透过率、电阻率以及探测器能谱响应等参数,综合评定了探测器用CdMnTe晶体的质量、电学和探测器性能。结果表明,晶片的红外透过率均在55%以上,最好可达到60%。采用湿法钝化,100 V偏压下的漏电流由钝化前的9.48 nA降为钝化后的7.90 nA,钝化后的电阻率为2.832×10¹⁰ Ω·cm。在-400 V反向偏压下,CdMnTe探测器对²⁴¹Am@59.5 keV γ射线源的能量分辨率在钝化前后分别为13.53%和12.51%,钝化后的电子迁移率寿命积为1.049×10^-3 cm²/V。研究了探测器的能量分辨率随电压的变化特性,当偏压≤400 V时,探测器的能量分辨率主要由载流子的收集效率决定,而当偏压>400 V时,能量分辨率由漏电流决定。本文研究结果表明,Te溶剂Bridgman法生长的CdMnTe晶体质量较好,电阻率和电子迁移率寿命积满足探测器制备需求。     

近紫外激发Gd2ZnTiO6∶Eu3+,Li+红色荧光粉的制备及荧光性能

采用溶胶-凝胶法成功制备出系列Eu³⁺掺杂和Li⁺、Eu³⁺共掺杂Gd₂ZnTiO₆红色荧光粉,并研究Li⁺、Eu³⁺掺杂对样品的晶体结构、微观形貌及发光性能的影响。结果显示,所制备的Gd₂ZnTiO₆∶Eu³⁺,Li⁺(GZT∶Eu³⁺,Li⁺) 荧光粉为双钙钛矿结构,属于单斜晶系(空间群:P2₁/n),大小为10 μm的无规则形状的颗粒。在395 nm近紫外光的激发下,GZT∶Eu³⁺的发射光谱展示出典型的Eu³⁺线状特征光谱,发射峰中心位于615 nm处,归属于Eu³⁺的⁵D₀→⁷F₂跃迁。Eu³⁺的最佳掺杂浓度为0.07(摩尔分数),样品显示明显的浓度猝灭效应,其机制为电偶极子-电偶极子(d-d)相互作用。此外,研究还发现,Li⁺掺杂对样品的晶体结构、微观形貌没有影响,但是一定量的Li⁺掺杂可以显著增强样品的荧光强度。当Li⁺浓度为0.05时,荧光粉发射主峰强度增强程度最大,提高至原来的4.3倍,说明通过Li⁺、Eu³⁺共掺杂可以获得高亮度的GZT红色荧光粉。GZT∶0.14Eu³⁺,0.05Li⁺荧光粉的CIE色坐标为(0.631 1,0.375 3)与标准红光色坐标(0.670,0.330)较为接近,是一种潜在的LED用红色荧光粉。     

DMF体系中Cu2O球晶的制备及形貌分析

以N,N-二甲基甲酰胺(DMF)为溶剂,通过改变铜源和表面活性剂,调控反应参数,溶剂热条件下制备了三维十字形、空心及实心的Cu₂O球晶。利用XRD、SEM等表征手段,分析探讨了工艺条件变化对Cu₂O球晶形貌的影响。研究表明,随着DMF浓度的增大,体系的还原能力增强,Cu⁺增多,溶液的过饱和度增大,Cu₂O晶体集合体形态由晶体结构控制的各向异性与对称性的球晶逐渐向各向同性球晶演变。十二烷基硫酸钠(SDS)、十六烷基三甲基溴化铵(CTAB)、聚乙烯吡咯烷酮(PVP)等表面活性剂有助于降低溶液的过饱和度,增加结晶质的表面扩散能力,有利于规则形态Cu₂O晶粒的形成。反应体系中,Cu(Ac)₂·H₂O水解生成的羧基与DMF中的甲酰基在高温下发生脱羧反应产生CO₂气体以及SDS发泡作用产生的气体是形成空心Cu₂O球晶的重要原因。     

ZnO超细纳米线阵列的制备及其电化学性能

以Zn(NO₃)₂· 6H₂O和C₆H₁₂N₄为原材料,采用二步水热法在碳纤维布上合成了形貌尺寸均匀的ZnO超细纳米线阵列。用 X 射线衍射(XRD)和扫描电镜(SEM)对其晶体结构和形貌进行了表征,利用恒流充放电测试等手段对其进行电化学性能测试。测试结果表明,材料表现出优异的电化学性能。在200 mA/g的电流密度下循环150次后,ZnO超细纳米线阵列仍然约有730 mAh/g的充放电比容量,库伦效率保持在95%以上。在1 200 mA/g的大倍率条件下,材料的充放电比容量依旧可达481 mAh/g左右,表现出十分良好的循环稳定性和可逆性能,是一种较为理想的锂离子电池负极复合材料。     

80.5 MeV/u碳离子诱发铜靶的放射性剩余产物测量

高能重带电粒子能直接穿透靶原子核外电子层,与原子核发生直接碰撞,发生散裂反应,产生一系列具有放射性的剩余产物核.重带电粒子诱发靶材放射性剩余核与辐射防护和人员安全有着密切联系,当前,大部分剩余核产额主要依靠蒙特卡罗粒子输运程序进行模拟计算,其准确程度亟需通过实验测量进行准确评估.本文利用能量为80.5 MeV/u的(12)^C⁶⁺粒子对薄铜靶开展了辐照实验与伽玛射线测量,结合伽玛谱学分析方法,得出了辐照产生的18种放射性剩余产物的初始活度和产生截面值,并与PHITS模拟结果进行对比.结果表明,PHITS模拟程序对放射性剩余核种类的估计具有较高可靠性,在其绝对产额方面,与实验测量仍具有较大偏差.     

A coupled immersed boundary‐lattice Boltzmann method with smoothed point interpolation method for fluid‐structure interaction problems

The immersed boundary‐lattice Boltzmann method has been verified to be an effective tool for fluid‐structure interaction simulation associated with thin and flexible bodies. The newly developed smoothed point interpolation method (S‐PIM) can handle the largely deformable solids owing to its softened model stiffness and insensitivity to mesh distortion. In this work, a novel coupled method has been proposed by combining the immersed boundary‐lattice Boltzmann method with the S‐PIM for fluid‐structure interaction problems with large‐displacement solids. The proposed method preserves the simplicity of the lattice Boltzmann method for fluid solvers, utilizes the S‐PIM to establish the realistic constitutive laws for nonlinear solids, and avoids mesh regeneration based on the frame of the immersed boundary method. Both two‐ and three‐dimensional numerical examples have been carried out to validate the accuracy, convergence, and stability of the proposed method in consideration of comparative results with referenced solutions.     

A class of time‐fractional reaction‐diffusion equation with nonlocal boundary condition

The purpose of the study is to analyze the time‐fractional reaction‐diffusion equation with nonlocal boundary condition. The proposed model is used to predict the invasion of tumor and its growth. Further, we establish the existence and uniqueness of a weak solution of the proposed model using the Faedo‐Galerkin method and compactness arguments.     

Stability-indicating RP-HPLC method development and validation for determination of nine impurities in apixaban tablet dosage forms. Robustness study by quality by design approach

A quality by design (QbD) based high-resolution HPLC method is described for determination of impurities in apixaban (APX) in the tablet dosage form. Employing a simple and stability-indicating HPLC method, nine known impurities were quantified with good peak resolution. Mobile phase A (MP-A) was prepared with buffer and acetonitrile 90:10 v/v, while mobile phase B (MP-B) contained water and acetonitrile 10:90 v/v. The gradient program was 0 min, MP-A 75%, B 25%; 20 min, MP-A 65%, B 35%; 30 min, MP-A 40%, B 60%; 40min, MP-A 40%, B 60%; 42 min, MP-A 75%, B 25%; and 50 min, MP-A 75%, B 25%. The chromatographic separation was achieved using a Zorbax RX C₁₈ 250 × 4.6 mm column, 5 μm (1.0 ml min⁻¹, 280 nm, 50 μl) and a column temperature of 40°C. Several separation studies were carried out using design of experiments to optimize the method. Validation results confirm the applicability of the developed method for quality analysis and stability studies of the regular product on the manufacturing stream.     

Polymerization kinetic pathways of epoxidized linseed oil with aliphatic bio-based dicarboxylic acids

The curing of epoxidized linseed oil (ELO) with three different bio-based dicarboxylic acids (sebacic acid, suberic acid, and succinic acid) has been investigated. No accelerators or catalysts were used and the resulting thermosets are 100% bio-based. Structural investigations of the three crosslinked ELO resins were made using FTIR spectroscopy and TMA, that is, tensile tests, TGA, and DMA. As evidenced by FTIR measurements ELO and dicarboxylic acids reacts but no major differences can be distinguished between the dicarboxylic acids. Non-isothermal curing has been conducted by rheological and DSC measurements. Advanced isoconversional analysis applied to DSC data in association with the complex viscosity variations gives new insights into the polymerization mechanism. The length of dicarboxylic acid carbon chain modifies the reaction rate. Then, a correlation between reaction rate, activation energy, pre-exponential factors, polymerization mechanism, and change in rate-limiting step was shown. DMA and tensile tests highlight the relationship between the carbon chain length, reactivity, and thermomechanical properties. The use of succinic acid allows reaching a higher T_g and thermal stability.     

基于Matlab GUI的微观化学反应过程可视化设计

Based on the quasi-classical trajectory (QCT) method and Matlab GUI technology, we developed a program code for visualizing the collision process of the elementary chemical reactions of the a + bc type. The general methodology of QCT, abstraction of dynamical properties of molecular collisions and the making of Graphical User Interface are introduced. The running results of an application to the reaction F + HCl→HF + Cl is also presented. The results showed that this program could vividly demonstrate the behavior and final state of the atom-diatom collision process in animated form. Students can interact with internal MATLAB code through graphical user interface, observe the reactive behavior and final results in real-time from multiple angles, which helps students to understand the complex reaction mechanism and deepen their perceptual impression of the chemical process at a microscopic atomic/molecular level.